Welcome to our Site for MG, Triumph and Austin-Healey Car Information.
MG Midget and Sprite Technical - Polyurethane Blue Bushes
| I haven’t used my car much for quite a while and just peaked underneath and was somewhat horrified to see my poly bushes in the rear spring hangers are crumbling to bits - just like poor rubber ones ! I’ll have to summon up enthusiasm over the weekend and drag myself underneath for a look see and do some maintenance- getting too old for all this ! These were the original Polybush make. |
| richard b |
| So far (> ±20 years?) no problems with power flex blue. I started with Polybusch red but they did not fit. |
| Flip Brühl |
| Think I posted a similar thing a while back. Mine completely disintegrated too with hardly any use , they were the rear spring pads and shackle bushes . They just crumbled and I just started to find bits of blue rubber on the garage floor . After a bit of research it appears there may have been a bad batch produced at some point and I had bought them from a private eBay seller but unused and in the original packaging . |
| Mike Fairclough |
| Thanks Mike Mine came from an MG supplier boxed. I had to bin the trunnion ones as they squashed out as I tried to fit them. So I fitted SuperPro ones that came with washers etc. Just hope the inner wishbone ones are ok ? Original rubber worked well enough when it was genuine parts ! |
| richard b |
| Richard I fitted super pro blue bushes to the front upper trunnions earlier this year - so far, so good but I won't know for a year or two if they're good quality. Other after market rubber is cracking like that on the rear radius arms (Moss). Track rod end gaiters ok so far (Moss). But, like Nick said in an earlier thread, "they really don't care, do they". |
| Bill B |
| My top trunnions from Superpro were the original yellow colour ones. Will have to summon enthusiasm to get under the car but difficult to muster! Hopefully replacement wont be too difficult as the springs should be rather more used to there residing position than when new - just don't want to have to fight them again ! Keep thinking its time to say goodbye ! That would be a sad day and rather admitting defeat ! Regular replacement of parts due to rubbish quality is getting past a joke ! |
| richard b |
| I fitted Polybushes in the late 1990's. It was a time when mainly only specialist supplied them. I bought a full car set for around £30, from the then Welsh MG centre in Wrexham. When they arrived they were packed in various unit sets in sealed bags with the Polybush logo. Except for the top trunion ones that were in plain unsealed bag with polybush and the application written on a sticky label.
They fitted well except for the pair on the top trunnion bolt. On both sides these just disintegrated. As I tightened the nut they bulged and then broke up into small chinks and crumbs. I complained to Welsh MG and after a bit of 'discussion' they supplied replacements a couple of weeks later. These came in a sealed Polybush bag. They looked the same but these fitted perfectly. What happened? Welsh MG were short of stock and had augmented their usual supplies from Polybush who are also in Wrexham, with some bought in elsewhere. They never said where from but although they looked the same they clearly weren't! Bushes like these must be pretty simple to produce and the market is very likely awash with poor quality copies. The technical bit is using the right polymers and controlled manufacture. The descriptive name polybush is now like hoover or dyson. Not all polybushes are actually Polybushes. My genuine Polybushes have been on the car for over 25 years and are still good! https://www.polybush.co.uk/about-us/?srsltid=AU7gw4WzW2FgZ9QHQ-9gmj6FIyn8e-4reDlQqvSuy8L6WZa2YEtvKfd1 |
| GuyW |
| Guy Very interesting my experience so similar and from Welsh MG, seem to remember still boxed and bagged. Only just seen the shackle ones breaking up. |
| richard b |
| I believe Welsh MG no longer exist. They were a reliable parts supplier at one time. I think on the occasion I described they had run out of genuine Polybushes and simply topped up from an alternative source - that turned out to be cheap rubbish copies. The genuine Polybush ones not only fit properly but then last for years! |
| GuyW |
| I don’t share your optimism Guy - mine were 2003 Welsh MG centre for £60 ! And Genuine Polybush kit - just found the box as it was storing other things ! Just checked and spring pads also shot ! Will order a set of Superpro ones and see. Rather concerned over the inner front ones know !
![]() |
| richard b |
More pics !
![]() |
| richard b |
| Hmm! Maybe I need to jack my car uo for an inspection! |
| GuyW |
| Richard, Does the box have any further information on it such as a batch code. Have you tried contacting Polybush to see what they make of it? |
| David Billington |
| You would almost think those had been in a fire! I know you have had a hot summer 'down south' but surely not that hot! 🔥 |
| GuyW |
| Guy I had the same experience as you with top trunnion bushes from Welsh MG centre, supposedly Polybush but absolute crap, just oozed out everywhere when tightened up. Rightly or wrongly I swore never to use Polybush again and now use Autobush which are very good. Les |
| Les Robinson |
| I also had their top trunnions squashing out and replaced them with the Superpro ones that came with thick washers. |
| richard b |
| Polybush do machinable polyurethane bar https://www.polybush.co.uk/advice-blog/machinable-polyurethane-bar/ and https://www.polybush.co.uk/product/pa00-machinable-poly-bar/ Opens some possibilities for those of us with a lathe. |
| David Billington |
| David I have contacted them with some pics and asked why they failed - especially as the original rubber lasted 30 years ! (not modern rubbish stuff !) How would you hold the poly bar in the lathe being jelly like ! Also what tools / speeds ? |
| richard b |
| Richard,
I would expect it would benefit from being held in a collet or soft jaws machined to suit the diameter to near fully support the OD and a sharp tool. I'm machining some wood at the moment and wanted minimal marking so 3D printed some jaw covers to suit the intended diameter and contact about 70% of the OD. I've machined acetal before now and that benefited from being held in a collet as I was using a form tool and it worked great (see image), held in a 3 jaw the acetal deflected and chattered. I expect the polyurethane bar is a firmer grade, I didn't see a shore hardness quoted.
|
| David Billington |
| https://www.polybush.co.uk/about-us/our-grades-explained/ gives 90 Shore A hardness for the machinable material. |
| David Billington |
| Well I received this response from Polybush.
Seems storing a car in a garage is not a good idea after all ! “This failure mode is common is areas of higher humidity where the bushes aren't getting used very much. It isn't something we see often however. Over a long period of time the bushes absorb moisture and start to swell, breakdown and degrade and turn into almost dust like form as your pictures demonstrate. Polyurethane is a fantastic material but this is it one draw back. In cases of standard usage and storage conditions we have seen our bushes last 20+ years without issue. The higher shore hardness bushes do not suffer anywhere near as badly as the softer 65 Shore A grade you have. I hope this answers your question.” If only we could get original rubber quality !!! |
| richard b |
| Maybe Australian super pro bushes are better then? Seem to be 70 shore minimum. |
| Bill B |
This thread was discussed between 01/10/2026 and 07/10/2026
MG Midget and Sprite Technical index
This thread is from the archives. Join the live MG Midget and Sprite Technical BBS now