MG-Cars.info

Welcome to our Site for MG, Triumph and Austin-Healey Car Information.

Recommendations

Parts

MG parts spares and accessories are available for MG T Series (TA, MG TB, MG TC, MG TD, MG TF), Magnette, MGA, Twin cam, MGB, MGBGT, MGC, MGC GT, MG Midget, Sprite and other MG models from British car spares company LBCarCo.

MG Midget and Sprite Technical - Rocker cover rubber seals

I am losing a lot of oil from the two rubber seals under the hold-down nuts. I have fitted new ones, to no avail. The part number is 12A 1358. I have more in stock, but I wonder if they will ever work. They are very loose around the tube nuts, and I can't see how they would seal. The parts list shows two packing washers, one thin and one thick, and even with both they still leak. My fading memory over 65 years is that the nut was always tight in the seal. Am I hallucinating?
Les Rose

Poor quality parts ?. Minispares mention they have their own made as import ones were poor https://www.minispares.com/12a1358-rocker-cover-rubber-grommet . I don't recall ever having them leak on any of my engines. Having rebuilt the rockers it reduced the oil in the rocker cover significantly.
David Billington

Les, are the two end pedestal studs fully down into the head? If not, the cover hold down nuts can bottom out before they seal.
GuyW

Good point Guy, but the studs are fully home and I can see the rubber seal is compressed. There's the possibility that the studs are too long, but the thick washer should compensate for that.

This reminds me that a couple of years ago when Sussex Classic Car Parts was clearing stock for closing down, I bought one of their alloy rocker covers as it was dirt cheap. I have never been able to get this to stop leaking, so I went back to the steel one. But I digress.

Meanwhile I have fitted new seals and both the thick and thin washers, and I'll see what happens. If these don't work I'll get the Minispares ones. I'm fairly sure that the cork gasket is OK - it's a new one - but if anyone has any recommendations I'll be glad to hear them.
Les Rose

Interesting digression Les, as I did the same (bought an alloy rocker cover from Sussex Spares) but have yet to fit it. Will try it and see it it has the same issue.
Jeremy MkIII

I have an alloy rocker cover, though as far as I recall I got it second hand at a car show. It doesn't leak. I glue the cork gasket to the cover as there is little to stop the long sides flapping around as you fit it. Then on the face that contacts the head I just give it a wipe of grease. I also put grease or vaseline on the stepped sealing washers though I'm not sure why I do that as grease and rubber don't usually go well together.
GuyW

Anyone using a period rocker cover. A Yimkin rocker cover was sold recently.

Alan Anstead

Les,

Can you add an O ring between the tube nut and rubber seal to see if that improves it. Any places in Salisbury that have O ring assortments if you haven't got your own.
David Billington

This is what mine looks like (1275), the rubber washer is stepped, the inner part fits into the rocker cover, the outer part is then compressed by the cover/washer and nut.

Never had any leakage either end, and the rubbers must be 50+ years old, I have never changed them...

Tim C

Tim, your washer is much thicker than mine. Do you tighten it until the nut bottoms, or just to squash the rubber a bit? I have never found these seals to last more than a couple of years, let alone 50! They usually go soft and fall apart.

Good idea Dave. If it still leaks I'll find an O-ring from my assorted stock.
Les Rose

The thick washer may be to take the place of the lifting eyes that some engines had fitted to those rocker cover studs.
David Billington

Dave
You are correct about the thick washers. I temporarily discard them to fit the lifting eyes when pulling engines out.
Alan Anstead

I have two sets of the lifting eyes, and the thick washers BUT never made the connection that some cars came with the lifting eyes !

But Les, you do IMO need the thick washers to make a seal
Malc Gilliver

I’ve never seen lifting eyes standard on Midgets - will
they clear the bonnet at the front ? Often on Morris Minors especially with replacement engines.

I’ve never really felt happy lifting on them as with the engine/ box angled there is a lot of twisting applied to relatively small bolts so I usually have a back up strap/ chain.
When I was stripping my restoration wreck I didn’t bother and one broke and the engine dropped luckily only a foot onto the shroud / slam panel which was being scrapped anyway!
Seems a previous owner when fitting the horrible alloy rocker cover filed the nut so it fitted the cover and I hadn’t spotted it - it’s quite a thin long nut section and it sheared right under the head.

Always use a back up now !
richard b

Over 57 years of Sprite ownership I have used the lifting eyes on many A-Series engines, both mine and others, and not experienced any problems using Haltrack, block-n-tackle, or my crane.

Alan Anstead

I use a welded link chain looped under the engine, back and front, and connected with a HT bolt and big washers. Then a hand operated weston differential chain winch hung from a ceiling rsj inserted for the purpose when I built the garage.

Before that upgrade I had one of those ubiquitous nylon stringed Haltrac hoists. But the nylon string was so oil soaked and miserable looking I never quite trusted it.
GuyW

Easier lifting with the engine the right way up.

David Billington

Les, any chance of a photo of your setup?
Paul Walbran

Here is my setup. Why does this BBS keep rotating photos? Anyway I have fitted new seals and the thick washers, and the leak is better but still present. I will now try the O-rings.

While rummaging round the engine I noticed a slight leak from the side covers. I have already replaced the front one with the standard cork. Also what do folks think about the best rocker cover gasket? I have just put a new cork one on, by sealing it onto the cover with silicone. I'm not convinced this has really worked. I tried a rubber one in the past but this didn't seem to be any better.

At risk of starting another oil sucking thread, I'll just mention that I have one breather (with oil separator) from the front side cover that goes to the manifold downstream of the throttle, without the PCV. The hole in the filler cap is blocked. This seems to have worked pretty well for the last three years or so.


Les Rose

Deapite what you may read, size matters. I reduced the file size.

Good old Haltrac.

Brilliant. Never let me down. Although the small version does wear the nylon wheels a bit. The bigger (mgb) version was better/easier to use.

I used my small Haltrac a lot.

I once used it on a building site on Crete in the early 80s. My silver seal ribcase had jammed -- for the 2nd time on the trip, in 1st gear. Firstly on an Autobahn on the way to Greece. After having it transported off to a garage, and supervising the pulling of the the engine and box there, a Volvo mechanic sorted it out, and showed me what went wrong with the 'silver seal'. He gave me a spare shim 'just in case'.

X number of weeks later, heading south on Crete, miles from any town or village, it locked in first again. Hours later, still in first gear I reached a town and found a building site. F*ck knows how, but I explained to some Greek builder I needed to use some of his scaffolding. My bird (Suzette) went off to buy beer and food, while I errected a scaffold over my Sprite, watched by ammused Greeks. Using my trusty Haltrac and a nylon tow rope, I pulled first my engine, and then my box. I stripped the box, added the 'just in case' shim, and put the whole shebang back in.

Meanwhile the Greeks had long since become less ammused, more bored, and drifted off. It was just getting dark as I finished. We went into town. I got pissed, and we slept as far as I can recall in my Sprite on that same building site.

The box was as good as gold(seal) for the rest of the tour of Crete, and journey back up through Europe to home, x weeks later.

When I got back to University Motors in Balham, I explained. They didn't believe me. They gave me another Silver seal box, but wouldn't pay for the Volvo mechanic. But I 'think' I claimed on my insurance.

Why did I even have my Haltrac with me?

For the same reason I had a tow rope. But why?

Just in case I had to pull myself out of a ditch, which is what happened the first time I drove my Sprite to Greece in 1979. The interior roads then between towns were frequently little better than donkey tracks, and dried up river beds with bloody great dips, just waiting to ensnare passing Sprites. 🤣🤣.

So, like the boy scout I never was, I was prepared 2nd time round. I took along my Haltrac and tow rope. For good measure I also used to pack a spare HG, a torque wrench, and a load of tools.

Even I find all that hard to believe now. And yet, it's all true, with *nothing* made up.

The stuff we did in our 20s eh? F*cking amazing. 😅.











anamnesis

Deapite what you may read, size matters. I reduced the file size.

Good old Haltrac.

Brilliant. Never let me down. Although the small version does wear the nylon wheels a bit. The bigger (mgb) version was better/easier to use.

I used my small Haltrac a lot.

I once used it on a building site on Crete in the early 80s. My silver seal ribcase had jammed -- for the 2nd time on the trip, in 1st gear. Firstly on an Autobahn on the way to Greece. After having it transported off to a garage, and supervising the pulling of the the engine and box there, a Volvo mechanic sorted it out, and showed me what went wrong with the 'silver seal'. He gave me a spare shim 'just in case'.

X number of weeks later, heading south on Crete, miles from any town or village, it locked in first again. Hours later, still in first gear we reached a town and found a building site. F*ck knows how, but I explained to some Greek builder I needed to use some of his scaffolding. My bird (Suzette) went off to buy beer and food, while I errected a scaffold over my Sprite, watched by ammused Greeks ( Cretans I guess I should say? Lol). Using my trusty Haltrac and a nylon tow rope, I pulled first my engine, and then my box. I stripped the box, added the 'just in case' shim, and put the whole shebang back in.

Meanwhile the Greeks had long since become less ammused, more bored, and drifted off. It was just getting dark as I finished. We went into town. I got pissed, and we slept as far as I can recall in my Sprite on that same building site.

The box was as good as gold(seal) for the rest of the tour of Crete, and journey back up through Europe to home, x weeks later.

When I got back to University Motors in Balham, I explained. They didn't believe me. They gave me another Silver seal box, but wouldn't pay for the Volvo mechanic. But I 'think' I claimed on my insurance.

Why did I even have my Haltrac with me?

For the same reason I had a tow rope.

But why?

Just in case I had to pull myself out of a ditch, which is what happened the first time I drove my Sprite to Greece in 1979. The interior roads then between towns were frequently little better than donkey tracks, and dried up river beds with bloody great dips, just waiting to ensnare passing Sprites. 🤣🤣.

So, like the boy scout I never was, I was prepared 2nd time round. I took along my Haltrac and tow rope. For good measure I also used to pack a spare HG, a torque wrench, and a load of tools.

Even I find all that hard to believe now. And yet, it's all true, with *nothing* made up.

The stuff we did in our 20s eh? F*cking amazing. 😅.



anamnesis

The one time I had my A series box jam in 1st I rather brutally drove it slowly and pulled it out of gear, it did come out, and didn't misbehave again but it hastened its demise and replacement with a 4 speed Ford gearbox out of an Escort. That BMC gearbox was a silver seal unit at about 3 years use. That was late 1980s.
David Billington

Les,

Are you using an automotive rated silicone sealant? Personally I've used Hylomar on the rocker cover gasket.
David Billington

Things we just got on with hen Anamn. Like you I have changed head gaskets on the roadside. And on one occasion after work and having had my tea I decided at 9 pm to take the engine out of my car (A35) to replace the clutch plate. I was due at a site meeting at 8am the next morning, some 70 miles away. Not sure what I would have done if I got stuck for some broken part or other!
GuyW

" we just got on with it then ". Yep, that'll be it Guy. We did. Wish I had a digital camera back then to record it all. Lol.

Meanwhile, after that sojournal type drift down memory lane, 😂.

" I have fitted new seals and the thick washers, and the leak is better but still present."

Les if you have a leak(s) there, you must have a fair amount of oil being thrown up there, and perhaps a distorted cover to boot.

Also, as regards the leak from the rocker cover to head gasket, you *mustn't* over tighten the two clamping nuts. If you do, you bend the rocker cover. It only really needs nipping up to compress both the cork gasket, and those two rubber seals on top. Even without 'sticking' the cork to the cover, you can get a leak free fit if you have a decent cover and gasket. But definitely it's easier if you use something to stick the cork to the cover as it holds it in place. I've re-used my cork multiple times.

Persevere.


anamnesis

Just back from a short local run and no sign of leak from the rocker cover. That's with an O-ring on one nut and a similar sized rubber washer on the other (only 1 O-ring in stock. If the rubber isn't tight around the tube nut there is a path for leakage through the gap between the metal washers and the nut. As I said before, my recollection is that the rubber seals were always tight around the nut, but they are not now.

Yes Dave, I always use the correct silicone sealant.

Anam, this is what I asked before. Do I tighten the tube nuts onto the studs, or do I just compress the seal a bit? I thought the washer thickness was designed not to distort the cover because the nuts bottomed before this could happen.

There is still a leak from the front side cover, so I'll have to replace that gasket. It's a 1098 cover so do I use rubber or cork?
Les Rose

Les, I think it depends on whether you have deep pressed or shallow covers.

And I can’t remember which goes on which?

The Moss catalogue might specify but I don’t have one where I am for the next few days.
Philip Sellen

I thought the original pressed steel rocker covers were all the same depth on all A series engines.

If your nuts are bottoming out on the studs, and the rubbers seals and cork aren't compressing enough, then either the studs are too long, or something else is off spec' I would think.

No I've never bottomed out my cover nuts, other than when the cover rubber seals were yonks old and had hardened and no longer compressed/expanded.

Are the news ones on offer the same thickness as the originals? I haven't bought new ones for years because they do last so long. The same with my cork, the one I have was bought a long while back. Are the new corks thick enough?

Also, have you checked your rocker cover faces for flatness?


anamnesis

No Anam, I’m referring to the side tappet chest covers - not the rocker cover.
Philip Sellen

Delineation rules. 😉 🤣.

anamnesis

Sorry to have gone slightly off topic with the side covers. I have the conical ones.

Anam, your diagram is for a 10CG engine, according to my parts list. I have never seen part 5, which is called a distance piece, on any of my engines. I would guess that this part would prevent any bottoming of the nut. The diagram might not be to scale, but it does suggest that the nut fits tightly into the seal.
Les Rose

Here is an image from the Workshop Manual for MK1 Midget. Looks like the nut is threaded on the outside, which is wrong, probably artistic licence...

Tim C

Les

Here are pics of bits from my spares/ scrap box.
The parts are from numerous engines likely 948 sprite/ moggie thousands, van engines etc.
Can’t remember them ever changing.

The rubber washer is stepped to receive the pressed steel cap with the thick washer on top.

Richard B.




richard b

Les
Only other thought is if you have previously tightened the cover right down hard you may have spread it and now not sealing.
Do you have a spare cover to try / Measure height from deck to bolting surface ?
richard b

Agreed Richard. Overtightening can bend and spread the cover.

Also, the rubber step sits inside the cover, not the cup washer.

anamnesis

The problem isn't the gasket between the cover and the cylinder head, it's the seal under the tube nut. I still think that the tube nut should fit tightly in the seal, but all the seals I have bought recently are loose. So far filling the gap with an O-ring seems to help.

Sorry to digress again, but does anyone else find that Gmail flags notifications from this site as spam?
Les Rose

"At risk of starting another oil sucking thread, I'll just mention that I have one breather (with oil separator) from the front side cover that goes to the manifold downstream of the throttle, without the PCV. The hole in the filler cap is blocked. "

*** The hole in the filler cap is blocked. ***

You know, I thought somehow this was all getting a bit deja vu.

Remember this Les? See the picture?

MG Midget and Sprite Technical - Testing a PCV valve

http://www.mgcars.net/mg-midget-sprite-technical-bbs/testing-a-pcv-valve-20220621120012200847.htm

Guy demonstrated very clearly what happens when blowby pressure builds under the rocker cover.

The amount of times this picture has been posted, Guy's due royalties I reckon. 🤣🤣.


Substitute your blocked filler cap for Guy's glove. Guy's glove expanded. Your filler cap doesn't. The pressure is exploiting the only other escape route. Your cap nut rubber seals.

The filler cap serves as both an inward air vent, and as a relief for when/if you have blowby pressure under the rocker cover.

Why have you blocked your filler cap hole?

Substitute your block for a gap.

Let the air out of your plastic mac.

😁

https://m.youtube.com/watch?v=eswQl-hcvU0


anamnesis

Found another (complete this time !) original rubber washer as per the pic

The tube nut is a very tight fit through the rubber washer, it also has a reduced diameter that sits into the rocker cover hole, the recess on topside of the rubber is caused by it pulling into the cup washer.

So if the rubber washers are loose send them back !

R.

richard b

No doubt they are made to a metric size now which might explain why they are loose.

Trev
T Mason

Mebee so. But if there's enough pressure under the rocker cover, even the correct sized rubbers will leak oil.

Les, I'm not sure what your car/engine is.

But you've changed the crankcase ventilation from an earlier version, to an invented hybrid version; -- and I think, that was to solve your earlier problem of bad idling with the mushroom type pcv valve.

Earlier, with the mushroom valve into the inlet manifold, you'd have had greater suction/evacuation internally, and less rocker cover pressure build up.

If you'd employed twin hs2 carbs and your current side cover vent setup, you'd have greater suction than you do now. The single HIF you have, has a lower suction on the side cover vent, that would twin HS2s.

I know because, --- a, I measured the difference between twin HS2 and single HIF vent suction. And b, because with twin HS2s I had oil sucking, but not when I replaced my twins with a single HIF44.

But in any event, you ** still need a vent/breather hole in the rocker cover **. Either the earlier rocker cover with a spout that used to vent into the air filter can, or the rocker cover you have now, but with a vented oil filler cap.

Unblock your oil filler cap hole.


All that said, you will NEVER get it perfect. The original design is flawed. There is piston blowby, there are no proper oil seals, and there is a desire/need, to protect the environment and the engine, from the effects of the blowby.

The engine is an old design, and everything regarding passive or positive crankcase ventilation added to it, is an imperfect compromise.

It'll leak oil and blow a bit out; -- either at the bottom via the rear crank scroll, or out of the dip stick orifice, or the top via the rocker cover.

The best you can do is minimise it.

You definitely need a vented rocker cover -- by either a vented cap or a spout.

Because you have carb venting, in order to create negative internal crank pressure, you need a restricted rocker vent. And that's by the use of the vented plastic oil filler cap.


anamnesis

Anam, click the link at the top of this thread to see my engine spec. Yes there was an earlier thread about idling with the mushroom valve. The breather setup I have now is based on the consensus at the time. It has worked fine for over 3 years, with no major leaks.
Les Rose

You have a leak(s) that bother you now though Les. Was there a concensus?

Reading back through that thread, your own last post in the thread was a rey to me

"Fair question Anam, but the idle is stable without the PCV and connecting the breather to the carb. The problem with that is that the leak is worse."

Yes, exactly.

And even if there wasn't a leak then, there is now, and that may be because crankcase pressure has increased due to the perhaps expected/inevitable increase in ring blowby, any extraction rate simply can't cope with it.

Have you tried unblocking the oil filler cap vent hole yet?

It shouldn't be blocked.



anamnesis

Revenons à nos moutons, as they say over the water, I just had an exchange with AH Spares and they say that the seals they supply are incorrect. At present their parts list says they are no longer available, and to use the AH 100 ones, but this turns out to be wrong. They say the correct ones have been ordered and will take up to 14 days to arrive. So I was right about something!

Anam, I have not looked at the filler cap because I have been distracted by stripping and respraying the boot top panel. The rocker cover seals are not leaking now because of the O rings, and that was my main concern. Nothing to stop me unblocking the cap to see what happens I suppose, but I doubt it will tell me much.
Les Rose

A bit of 'frog' huh? Lol. That's a neat way to end the drift. 👍.

I must admit, I've lost track. I thought that despite the addition of o rings, you still had oil leaking at the rocker cover cap bolt seals.

If you haven't, then what's the issue? You've fixed it haven't you?

But you should understand the purpose of the oil filler cap vent hole.

If you seal the engine completely, and apply suction, if the suction is great enough, you will create a vacuum in the crankcase. So far so good. That's actually good for bhp.

https://inthegaragemedia.com/horsepower-from-nothing/

But, it doesn't evacuate condensation and the other gasses that degrade the oil, and hence harm the engine.

Hey ho though. You pays yer money you makes yer choice. 🙂. The choice depends on your objective.

Forgot to say. I followed your profile link. Super nice looking Frogeye. 🙂.



anamnesis

Thanks Anam, but that photo doesn't show the boot which is what I'm redoing now.
Les Rose

This thread was discussed between 24/09/2026 and 09/10/2026

MG Midget and Sprite Technical index

This thread is from the archives. Join the live MG Midget and Sprite Technical BBS now