MG-Cars.info

Welcome to our Site for MG, Triumph and Austin-Healey Car Information.

Recommendations

Parts

MG parts spares and accessories are available for MG T Series (TA, MG TB, MG TC, MG TD, MG TF), Magnette, MGA, Twin cam, MGB, MGBGT, MGC, MGC GT, MG Midget, Sprite and other MG models from British car spares company LBCarCo.

MG MGB Technical - 4 sp trans ???....layshaft float & ball brg

Hi all, need your help with my rebuild of this later 4 sp non O/D trans. While taking off the front plate or extracting one of the selector rods (not sure which) I noticed a ball bearing had dropped out of somewhere from the front bellhousing. Any idea where this might go? My Haynes does not show a ball anywhere so I am thinking could it be under the spring that goes into the detent of the selector rod?

My other question is with the layshaft. I measured the clearance and it measured .011", Haynes says to have no more than .003" Is this correct? How critical is this float?

I also noticed that while taking off the front plate there are two shims against the front bearing. Their condition does show some where and one of them has a tear across it almost all the way. Should these be replaced with the same thickness or reuse?

Thanks for your help and understanding.

paul
PRC

Hi Paul,

For the shims, you are supposed to measure the depth of the front cover and how much the bearing protrudes from the front of the gearbox casing, subtract a bit for the gasket, and still end up with a few thou (can't remember how many) of clamping so that the bearing is held firm in the case. Wear on your shims may indicate wear on the aluminium parts also, so you should re-measure and fit the prescribed thickness of shims rather than just fitting the same again.

The ball bearing, yes - sounds like it was the detent spring. They fit from the top of the gearbox casing, bellhousing end - under three hex-headed plungers.

hth,
--
Olly
Oliver Stephenson

Olly, thanks for your input. I have another question maybe you can answer or should I start a new thread?
The shimming on the front plate, are they there to put crush on the brg to keep it from rotating? I ask because I had a pretty tough time removing the first motion shaft from the case because the brg was a pretty tight fit, I don't see how it could rotate without any crush from the cover. Or should there be clearance btw the brg face and cover?
I am checking the shims on disassembly so I can understand on the reassembly.
Thank you.

paul
PRC

Paul,

The crush is there just to stop any chance of the bearing moving fore and aft in the casing, which would allow the first motion shaft to move forward slightly. I'm sure the 'box will survive for a while with no clamping load, but some crush is prescribed by the factory so I think it's best to take their advice :o)

Do you have a Bentley workshop manual? It has the only useful gearbox rebuild manual, ignore Haynes. If you don't, I'll try to remember to look up how many thou of crush you're supposed to have when I'm next in the garage!

ttfn,
--
Olly
Oliver Stephenson

Olly, I was doing some more reading in my haynes (maybe a bad thing) and it said to leave about .001-.002" clearance btw the shim and brg face, this allows the cover gasket to be sure it seals, otherwise you would never be able to properly seal against the cover to case. It makes sense I guess.
What does the Bentley say?

Thanks, paul
PRC

Paul,

The Bentley book assumes a certain thickness for the compressed gasket, but obviously the new gasket plus hermetite is thicker than this value so there is some squash on the gasket as well as clamping on the bearing when it's all torqued down.

Book isn't here, will look at the weekend when I have access to it :o)

hth,
--
Olly
Oliver Stephenson

This thread was discussed between 22/01/2007 and 23/01/2007

MG MGB Technical index

This thread is from the archives. Join the live MG MGB Technical BBS now