Welcome to our Site for MG, Triumph and Austin-Healey Car Information.
MG MGB Technical - High Beam/Ignition light wiring
| This may be a stupid question but… I’m having to replace the blue high beam light and the red ignition warning light on my 1970 MGB. The only replacements available are a different design from the originals in my car. The originals had a bulb inserted into the plastic light fixture. The replacements are total self contained units with 2 electrical nipples on the ends. So, do I just connect the designated hot wires for each device to one nipple and a ground to the other? Thanks for any help. |
| danny jacob |
| Why can't you replace like with like? |
| Dave O'Neill |
| For the ignition light; one terminal should connect to the brown/yellow wire that goes to the alternator and the other terminal connects to a white wire that goes to the ignition switch. High beam indicator; one terminal connects to the blue/white coming from the high beam switch and the other terminal connects to ground. |
| Kimberly |
| thank you for the feedback. there is no "like with like" replacements for these specific Blue & Red instrunment panel lights that I have found for my 1970 model. My old parts had plastic faces with raised octogon shapes, the replacements are flat with a dull aluminum surround. I will have to cut the wires bearing the bulbs and put a connector on the new replacements... unless someone knows a source for the original parts. |
| Danny Jacob |
| Do your old lights not have a bulb-holder which pulls out of the back, which has a replacable bulb in? |
| Dave O'Neill |
| A source for good used replacements maybe the theautoist.com Where did you get your replacements from? |
| Kimberly |
| Dave, it's not a problem with the bulb... the face of my panel lights, the bulb holder type, have faded terribly somehow. example, the blue light is almost white. Kimberly, Moss and VB sell different type relacements entirely ...as I've tried to described. This is a small matter by comparison but I'm trying to keep to the car's original design as much as possible and within reason. thank you. |
| Danny Jacob |
| Sorry, I obviously misunderstood the question. I just checked the Autosparks site and found this... http://www.autosparks.co.uk/store/catalogue/images/l/000677.jpg which obviously isn't original spec, either. I know what you mean about the fading lenses, though. I suppose the only other option is to find some secondhand ones. I know I salvaged some from a Riley Kestrel dash, but not sure which colours they were. |
| Dave O'Neill |
| I recall having the same bulb holders (raised octagon lenses) in my '71, way back in the day. I haven't seen them since, though. I looked at the VB and Moss catalogs and I think I see what you're saying about that. If you want to retain the original bulb holder style light, secondhand may be the only way to go. These things can be re-habbed pretty cleanly, but in your case the lens is badly faded so re-habbing probably isn't an option. Check out these pics and see if they're helpful. The first ( http://img259.imageshack.us/img259/461/bulbholders8xp.jpg ) is a set of bulb-holders I have in hand (these are holders, not integrated bulb/holder units). The silver bezels are NOT as well-maintained as they look in the picture. The second picture ( http://img309.imageshack.us/img309/2059/accontrol8hf.jpg ) is just to show how cleanly these things can be re-habbed. This is one of a set of A/C vents that were cleaned up for installation. I used a lot of careful masking, patience, and Testor's silver paint. Interestingly, Danny, I'm "tweaking" my dash a bit and replacing the old-style bulb holder with the new integrated type bulb. What you see here is a set of spares I no longer need. They are NOT the same as the ones you're looking for but if you can use them they're yours for the cost of a postage stamp. R. |
| Rick Stevens |
| thanks again. I'm glad I exhausted all my resources before wasting every one's time on this. It's remarkable how many parts are available for all model years but there are still some small detail parts that make me wonder how anyone can claim to have a fully restored MG. |
| Danny Jacob |
| The lenses were faceted (i.e. like a jewel). If octagonal it would purely have been coincidence as they were out of the corporate parts bin. The days of slapping octagons everywhere (including places totally invisible when the car was fully assembled) died with Kimber. |
| Paul Hunt 2 |
This thread was discussed between 19/01/2007 and 21/01/2007
MG MGB Technical index
This thread is from the archives. Join the live MG MGB Technical BBS now