MG-Cars.info

Welcome to our Site for MG, Triumph and Austin-Healey Car Information.

Recommendations

Parts

MG parts spares and accessories are available for MG T Series (TA, MG TB, MG TC, MG TD, MG TF), Magnette, MGA, Twin cam, MGB, MGBGT, MGC, MGC GT, MG Midget, Sprite and other MG models from British car spares company LBCarCo.

MG MGB Technical - I think I screwed up my dizzy

I was giving her a mini tune up today with new plugs, and cleaned and gapped the points. Where I think I screwed up, though it isn't something that is expected on any other car, is when I went to pull the rotor off I found it was on really tight so I really pulled on it and the shaft came up about an inch.

Now I usually use a screwdriver to wedge in between the rotor and the shaft it sits on to separate it, but this time I just pulled on it. Is the drive shaft for the distributors two piece that presses into the other?
If you ask me its kind of stupid and very weak design that could leave you stranded somewhere if the shaft dislodged(?) itself.

What's the deal with these things? I was able to turn the shaft until it stepped down to where the points rubbing block was centered on the cam lobes, but its still loose.
Can I get away with just removing the rotor and tapping the shaft with a hammer to secure it? I want to avoid having to remove the distributor and throwing the timing off.

Did I mention that Haynes exploded diagrams suck?
BurgerCokeFries

What a maroon.
CheeseburgerCheeseburgerPepsi

what an asshole
BurgerCokeFries

As far as I know that shaft is one piece, if it pulled out that far you have something seriously wrong, I'm sure plenty of distributor experts will pipe up but I would think you need to pull the distributor and see what exactly broke, I would not drive the car until that had been done.
The Wiz

BCF - If you lookat the top of the shaft, you should see a screw in it. The purpose of the screw is to hold the cam portion of the distributor onto the main shaft and to allow it to turn as the cintrifical weights respond tothe rotation of the shaft, thus advancing the spark as the engine RPM incerases (this is the mechanical advance for the distributor). This is not a weak design, it is standard, and if th screw is loose or missing, I would chalk it up to poor maintenance on the part of someone(previous owner?). The shop manual calls for periodic lubrication of this area, and hte screw should be hecked each time it is lubricated. Cheers - Dave
David DuBois

You know I thought there was a screw in there. Its a rebuilt unit I bought at a local parts house, and it never gave me trouble. In fact it ran so much better over the old unit.
I wouldn't be surprised if they forgot to install the screw. Ill check that tomorrow. Thanks chaps.
BurgerCokeFries

I had a similar problem when I was oiling an older dizzy. I pulled up a bit by accident and didn't get it back down far enough. The weights slipped off and jammed the dizzy. I was lucky to strip the cam gear off rather than destroy the whole unit.

When the screw is off, don't pull up! Guess I'm a maroon too. ;)
Steve Simmons

You're going to have to dig a little deeper here if you have lifted the cam about an inch as there is a good chance you have dislodged the advance springs which are located under the top plate. Remove the top plate by unscrewing the screws on the side and check that the springs are in place or otherwise relocate them. Hopefully they will not have sustained any damage and been stretched. Then replace the screw tightly to retain the assembly.
Iain MacKintosh

An inch is almost certainly going to have either stretched or dislodged the advance springs, hopefully the latter then they may not have stretched. I think whether a top screw exists or not depends on the model, either 25D or 45D, but I can't recall which is which. There may also be a plug in the hole over the screw. The shaft is in two pieces on both of them, that is what allows centrifugal advance to occur. I can't really see how you are going to put this right with the distributor in-situ, even on a LHD car.
Paul Hunt 2

I was thinking about this last night after looking at the Haynes book again and Im hoping luck is on my side and I didnt ruin the springs. I think I still have the original distributor so I might be able to use the springs out of that.
Ill have to take a closer look because for some reason the baseplate isnt moving as freely as it was before this happened. This would mean that the upper shaft hasnt seated as far down as its supposed to be.
Ill most likely pull the distributor to save my lower back.
By the way, the book shows the 25D series have the screw. I cant believe the 45D's dont.
BurgerCokeFries

The 45D has a nylon top hat washer that fits over a ball on the end of the inner shaft.
You have to remove the baseplate (2 screws) to see what has happened inside.

What normally happens is that one of the bob weights isn't located on the pivot pin on the outer shaft.

It should all go together again.
Note: one of the springs is supposed to be a rattling loose fit.
Martin Layton

This did happen to me once but not on my car. The rotor arm actually pulled up on the splines of the skew gear. That dizzy had to be rebuilt but it still work OK-ish afterwards, although the springs did not have much effect.
Stan Best

Chances are good that you have the 45d with the plastic POS clip that holds the advance assembly together. I'm not sure if you live in the US, but part of my rebuilds on the 45D includes modifying the shaft to actually be held together with a screw. This also allows me to adjust the end float to within more acceptible levels than the factory standards.

If you want to fix it yourself, remove the points plate and disconnect the advance springs before you ruin them. mark the orientation of the cam to the shaft - it can be reassembled 180 degres off. Put the weights on their posts. Remove the small plaastic piece from the center shaft and place it onthe cam assembly, lowering the two pieces onto the shaft together. Once they bottom out, reinstall the plastic clip to hold it together, if there's anything left of it. You may be able to use an old points insulator in its place with a little creativity. Install the springs last!
Jeff
Jeff Schlemmer

Martin, I couldn't help but notice that the heavier spring is a little loose. I compared it to the other distributor I have, so I figured it was right. Its good to read that anyway.
I went ahead and compressed that spring with some needle nose pliers just to be sure anyway.

By the way, its the 25D that I have, and yes that screw was completely out. I was hoping the thread boss wasn't stripped and it wasn't. I tightened it up real tight. Now there's no play in it all, so this just might let me bump the timing up a bit, now that it will be consistent.

I did have to pull the dizzy out anyway because the weights were off their pivots, but I was surprised how easily the baseplates came out.
I have to say though, I'm sure glad this happen now. It would have left me stranded somewhere eventually. I will definitely be staying on top of checking that as part of my routine.

One last thing, if anyone here has ever changed their condenser screw with their own screw (for whatever reason) make sure that it is no more than 3/16" long. Any longer than this and your advance will not work, because it pushes against the lower (fixed) plate.

Thanks everyone, she's better than ok now.
BurgerCokeFries

Duh! Martin specifically stated that one of the springs is *supposed* to be a loose fit! This *is* the heavier one, this arrangement is what gives a centrifugal timing 'curve' and not a straight line. I say 'curve' but it is actually two straight-ish lines joined by a knee. The first, thinner spring which is stretched onto the pins gives a steep advance for the lower rpms, then the loose, heavier spring comes into play to give a flatter curve for the higher rpms.
Paul Hunt 2

Yeah, well I know. But as I said before, "its good to read that anyway".
BurgerCokeFries

Actually, it's usually supposed to be a loose fit, but they do stretch over time. You may find that the car runs better (in many cases) with less slop in the secondary spring!
Jeff
Jeff Schlemmer

Having the secondary, thicker spring (which is the one that should be loose on the pins) tight on its pins will significantly reduce the rate of change of initial centrifugal advance and only achieve maximum advance at significantly higher revs. With respect I have to say that for otherwise correct springs and timing there is no way that will result in the engine running better.
Paul Hunt 2

Paul, You're making an assumption that his old dizzy has "otherwise correct springs." Do you know how rare that is? I receive maybe 1 out of 200 dizzys that has the correct curve in it, mostly due to fatigued springs. Shortening the secondary and replacing the primary is good medicine!

Jeff Schlemmer

I'm not making any such assumption which is why I used the term! If I *hadn't* used the term your comment would be justified. Tweaking or replacing (and I've not found anyone yet who has the *correct* springs to replace them with) stretched or tired springs is indeed the correct way to go, but I'd hate to think of anyone taking the required play out of the secondary spring as a matter of course expecting it to give them some performance advantage.
Paul Hunt 2

This thread was discussed between 19/01/2007 and 29/01/2007

MG MGB Technical index

This thread is from the archives. Join the live MG MGB Technical BBS now