MG-Cars.info

Welcome to our Site for MG, Triumph and Austin-Healey Car Information.

Recommendations

Parts

MG parts spares and accessories are available for MG T Series (TA, MG TB, MG TC, MG TD, MG TF), Magnette, MGA, Twin cam, MGB, MGBGT, MGC, MGC GT, MG Midget, Sprite and other MG models from British car spares company LBCarCo.

MG MGB Technical - Screeching front brakes

The screeching front brakes on my 71 roadster is driving me nuts, I have tried all sorts to cure them. New discs. Callipers, 2 different types of brake pads, using copper slip on the backs of the pads, even cut a groove in the pads and nothing seems to work for long. I don’t think that shims are made for the B pads unless someone knows better. Any ideas appreciated.
Trevor Harvey

Very common! Were any of the pads sets chamfered? That is supposed to be one of the 'cures' but only helped for the first few trips. Did any of them have a rubberised backing? My roadster may have those in at the moment. A set of V8 pads came complete with shims but squealed.

The only (at least, I stopped trying different things at that point!) thing that worked for me (although it has only happened on the V8 even though I've owned the roadster longer) was Bremtech self-adhesive foam pads stuck to the metal backing. Even that didn't stop it at first but I noticed that the pads were quite a loose fit in the (remanufactured) calipers. The edges of the metal backing were shiny which indicated to me they had been vibrating, I had some off-cuts from the Bremtech enough to stick a strip down each edge of each pad but still just get them in the calipers. Slight squeaks initially but then stopped and didn't come back. After some time I took the pads out of one of the calipers and the foam backing and edge strips were battered but still present, refitted and still quiet.

Not expecting that to work I bought some CRC disc brake quiet which puts a rubbery coating on the backing, never used it of course, loads of similar products on eBay.

This https://www.ebay.co.uk/itm/235578461211 claims to be Bremtech but different to what I bought and includes a Bremtech goo for metal to metal contact points in brakes so not exactly the same and similar to copper grease.

Mintex seem to do similar at triple the price.
paulh4

Thank for your reply Paul. I have removed the pads and as you can see the pistons in the calliper do not seem to contact the pads squarely. This surprises me as I would expect squarer contact. These Delphi pads do have a backing attached but the pistons have cut through them causing metal to metal contact, is this the cause of the squealing, they have been chamfered on the ends
There is signs of shiney ends on the pads so will see if I can get some of the 3M material that I have on to them. Thanks again,I value your help. Trev





Trevor Harvey

My front brakes squealed after I fitted Mintex 1144 pads, despite the use of copper grease.

Last year, I fitted a complete set of discs and pads to my daily driver and I also bought a tube of ceramic grease from Euro Car Parts.

I tried the grease on the B pads and it stopped them squealing.
Dave O'Neill 2

The second image looks like it has a stepped or two piece back-plate, not seen that before, mine have a flat back.

That also shows fairly equal pressure all round from the piston although it is offset towards the inner (when fitted) edge edge as that is how the pads are bonded to the backplate, your pressure points do seem biased towards the inner edge.

Where does your piston cutout face? The WSM shows it positioned towards the spindle and yours look to be the same, whereas I have seen drawings for the MGA with it facing outwards and on the Midget up or down!

I've had V8 pads with shims with a cut-out in half of one side, so who knows what effect that has when combined with the piston cutout.





paulh4

On a closer look these Delphi pads do have a thin steel backing plate attached to the pad and then coated with something.
I have stuck some thin strips of the 3M material on the edges of the pads to take up any excessive play, coated all contact points with copper slip and reassembled. I am fairly confident it will be quiet for about ten miles and then start squealing again.
This makes me think as the brakes get warmed up maybe the copperslip melts and no longer does its job, think I’ll get some of this ceramic grease that Dave O’Neill recommends and give that a try. Thanks Trev
Trevor Harvey

I meant to say that yes Paul the cut out point on the calliper pistons do face toward the centre of the wheel hub, I did wonder if this was correct.
Trevor Harvey

Is there a correct way round that the spring retaining clips go that hold the pads in to the calliper as one side legs are longer than the other.
Trevor Harvey

Yes, as attached.

paulh4

Trev-
An old trick we used to use when truck brakes squealed, was to get some carbon dust on a cloth and wipe it all over the linings. You can get the same result with disc pads by getting a pencil like a wide carpenter's pencil and scribbling over the braking face of the pads.
----"BE CAREFULL"--- first roadtest as the braking power is very deminished until the carbon rubs into the pad lining--only takes a lap around the block to return to normal braking power---but be carefull-
William Revit

William, not heard of that one before but will certainly give it a try next time they start squealing again as I expect they will.thanks
Trevor Harvey

Locksmiths graphite powder? The carpenters pencil being graphite?
paulh4

I have re assembled the front brakes again using both ceramic grease and pencil graphite and yes it did need a bit of careful driving after for a while. Have only done about forty miles since and had no squealing for most of those miles but towards the end of my trip some squealing was strarting to be heard again. I have purchased another different brand of pads which will be the third set and will fit them if it gets as loud as previous.
Trevor Harvey

Tried all the tips that has been advised, several worked for a short time but then the squealing came back.
I bought yet another set of brake pads (that’s the third set) Borg and Beck, they have a very thin metal backing to them, fitted them using ceramic grease and have driven over a hundred miles since and no squealing , yippee. It also giving me a better firmer brake pedal. So maybe I’ve cracked it. Thanks for all the advice .
Trevor Harvey

Good to (not!) hear :o)
paulh4

Just an update to this thread. After fitting the Borg and Beck pads and now driven about 750 miles the squealing has not returned so it appears that it was the pads all along that was the problem. Thanks for all the help and advice.
Trevor Harvey

This thread was discussed between 12/04/2026 and 31/08/2026

MG MGB Technical index

This thread is from the archives. Join the live MG MGB Technical BBS now