MG-Cars.info

Welcome to our Site for MG, Triumph and Austin-Healey Car Information.

Recommendations

Parts

MG parts spares and accessories are available for MG T Series (TA, MG TB, MG TC, MG TD, MG TF), Magnette, MGA, Twin cam, MGB, MGBGT, MGC, MGC GT, MG Midget, Sprite and other MG models from British car spares company LBCarCo.

MG MGF Technical - Coolant drainin/ replacement hose

I have a leak from th 40mm hose where it leaves the left front engine...
It already has a Jubilee clip, and the rubber is very pinched.
I am keen to drain the coolant/replace hose and refill/bleed.

I know about bleed points having done them before but how is it best to drain the coolant, and any preacutions on refilling an empty ystem (other than those too numerous to mention in the archive)

It's an N Reg VVC, and the local dealer was unsure of the part no. but sure it was not in stock. Is it OK to leave the engine 'coolant free' for 24 hrs? whilst awaiting the new hose

Many thanks




ps how do I change login details to Kent UK, NOT USA

Charles Dundas

Drain by removing the large hoses which run underneath to the front of the car. Just undo clip and pull off at one end. Remove the rad cap of course to let air in. I would get the coolant inhibitor back in before driving.

To change your details:-

From the main front page of the site select My Details and change them. You will need your password!

HTH

Bruce
Bruce Caldwell

Thanks...
It has sat in the garage for weeks.....battery went flat, tax ran out and other demands on my money meant it has been untouched for all that time.

I have just had a look at it again, new battery in and......


Click. oops, reset immobiliser
turn and Vroom. Started first time almost immediately.

At least something works.


charlie

Charles Dundas

Hi,

I think Robs and my webside still cover applicable stand of the art data due to bleeding the system
http://www.mgfcar.de/bleed/index.htm (and click also the links on top)
Some newer and different suggestions related to bleeding works are in the archives though.

After 24h I would in any way release the 'fourth' bleed location. The jiggle valve right hand down near the oil stick assy.

Regards
Dieter
Dieter Koennecke

Just checked with MGR.......Part No's have all changed....no idea when it may become available.....blah blah blah....


I almost laughed so hard my 'hose' split!! NOT

Will try breakers now.
charlie
charlie dundas

>Will try breakers now.

Let me know if this fails and you'd be desperate on replacing.
Got a complete set second hand at home.

>40mm hose where it leaves the left front engine.
Brief description on which you need, though.
http://www.mgfcar.de/hose_clamp/coolant.jpg
#13?
Dieter Koennecke

thank you Dieter, No. 15 I think but I have mailed a picture
charlie
charlie Dundas

got it and up to
http://www.mgfcar.de/bleed/leak.JPG

Indeed it looks like #15
And I know of two other cases where just this went.

I think you can get it as well at stores for any car cooling equipment, cause from my memory it's only a 90° bend hose with app 40mm outer diameter. So fo sure any standard

Any suggestions here ??
I can measure only next weekend.

Dieter

PS. for the webmasters without FTP abilities, whyever:
Found a nice tool to upload pics from behind a firewall with no port 21 access ;) HTTP only, dunno who this works, though it's great.
http://www2ftp.de/ (german language only) but works great to all my web accounts out there.
Dieter Koennecke

I'm afraid, but on second view I remember.
No 15 is made from two hoses ? or three ?
Put one in the other and adhered (vulanised?)
So a kind of reduction joint down or T-joint to diameter 29 mm and 40mm (outer)

Anyway, useless to assume anything without holding it in my hands.

I'm sorry for the confusion.

Regards
Dieter
Dieter Koennecke

Charles/Dieter,
I had one of the connectors from No. 15 to No. 16 go. It had been squashed by the addition and overtightening of a cheap jubilee clip to replace the Rover "snap" clip. The connector is identical to that shown to the left of No. 13.

Following replacement of this connector, the joint continued to leak slightly. I eventually removed the hose assembly no. 15 (which was a one piece unit). The hose at the connector was slightly split where it had been "scissored" by the clamp against the squashed connector.

A look in the Manual (rev 6) showed item 15 as being made up of 3 seperate parts. Went to my dealer, and asked if it was possible to replace just the "leg" section going to the heater run (as this would probably be cheaper that the complete assembly).
He looked it up and only 1 part number was given for the complete 3 part assembly.

On receipt of the hose, it is indeed made up of 3 seperate hoses, and a "Y" branch. They are not apparrently available seperatly, but only cost £36 as a complete unit. Fitted, system bled and no further leaks.

Paul
Paul Lane

Same problem here, the hose is deeply 'squashed' by a jubilee clip.....
Charles Dundas

At the suggestion of Moto-Build I called the dealer again as they can actually request specific info , forgotten the phrase, but it results in info on when the part will be available ie soon/later/forget it....

Result...hose should be in stock and delivered to the dealer next week.
Thanks Moto-Build
charlie
Charles Dun

With regard to refilling with coolant...

Can this be done 'single handed?'

Mention is made in the archive of topping up with the rad/heater bleeds open and ensuring the expansion tank stays full, to prevent air getting in whilst refilling.

Presumably if I pit in say ~ 5 litres coolant, I should be able to then close the two bleed points without the expansion tank emptying?

Any particular tips on refilling an empty system?

charlie
Charles Dundas

In fact if anyone has the relevant pages from the workshop manual I would be very grateful if you could email them to me.
regards
Charlie
Charlie Dundas

Hi,

I took a picture today from the Y-branch #15

http://www.mgfcar.de/bleed/rear_upper_cp_0407.jpg
(the upper)

HTH
Dieter
PS. some coolant related things now on http://www.mgfcar.de/bleed/
Dieter Koennecke

Charles,
I have drained and refilled my coolant several times (due to the pesistant leak noted in my posting above).
If you follow Roger Parkers/Deiters instructions (see the Archives) or the article in the MG owners mag a couple of months ago, it's actually straight forward.

Be methodical and take your time. When I have done it, it takes as long to bleed the system as to do the job for why you then need to do a fill/bleed!

No problems doing it single handed, the rate of bleed is controlled by you, so you casn open the bleed valves, keep the reservoir topped up, and close the bleed points one at a time.

I would suggest using a brake bleed type hose to direct the water away from the bulkhead when you bleed the heater nipple, as if you don't, some coolant can enter the cabin via the the nipple access hole, then the car steams up and stinks of "hot coolant" as the heater gets hot! most alarming. I now use discarded hoses from aircraft passenger oxygen masks (5mm polyvinyl stock hose will do).

In my experience, the heater circuit is the most stubborn to get all the air out of. Even when you are happy that it's all out, after a test drive you get a fresh steady stream of tiny bubbles.
Ensure the Heater knob is selected "full hot" to allow flow through this circuit.

Don't be afraid to tackle this job yourself, there are a lot of scary stories out there of Dealers not bleeding the systems properly (it happened to me). This doesn't mean its hard, just that they don't know what they are doing, or don't take the time to do it properly. If you do it yourself, then it will be as good as the care and time you take over it.

Regards
Paul
Paul Lane

This thread was discussed between 19/03/2002 and 27/03/2002

MG MGF Technical index

This thread is from the archives. Join the live MG MGF Technical BBS now