MG-Cars.info

Welcome to our Site for MG, Triumph and Austin-Healey Car Information.

Recommendations

Parts

MG parts spares and accessories are available for MG T Series (TA, MG TB, MG TC, MG TD, MG TF), Magnette, MGA, Twin cam, MGB, MGBGT, MGC, MGC GT, MG Midget, Sprite and other MG models from British car spares company LBCarCo.

MG MGF Technical - Coolant liquid leak, oil leak, (Mike Satur) head gasket: advice needed

Last week I went to change oil and they found out traces of coolant liquid leaks. Next day we put the coolant system under pressure (1.4 bar) and waited half an hour to find out that there is a leak between engine and gearbox.
The engine also has an oil leak that's been going on for a long time even (but the oil level dosen't show any drop).
I will have the engine removed to fix the coolant leak, mechanic says is one of the iron "stoppers" (don't know the right term) put in the engine that has corroded.
My mechanic also says it would be advisable to change the head gasket. So, question is: should I change it while the engine is out? and if so, what about the Mike Satur HG? Does it come by itself or do they sell it with the kit of parts the Rover one has?
I don't know if I've been clear enough, but any advice will be deeply appreciated.
Thanks,
Gian Marco
Gian Marco Mazzocchi

Gian,
The "iron stoppers" sound like "freeze plugs". They are put in to stop the engine block from cracking if the engine coolant freezes; in theory they are the first to break before the block.
Whether to replace the head gasket at this point is subjective. If you trust your mechanic take his advice, he has the engine to look at. There are several factors to suggest a replacement head gasket, although none would be entirely conclusive without removing the head to look at the gasket itself. IMO, if your mechanic suggests a replacement, replace it. Use steel dowls, and the best gasket you can buy. The cost of parts is negligable compared to the labour involved, a good chunk of the labour is removing the engine. Good luck
george

Core Plugs we used to call them - they were a result of the casting operation and as I understand it were not actually 'put there' but arrived!

Also my understanding is that the engine does not actually have to come out for head gasket or cam belt work but probably will to replace a weeping core plug.

As George says the materials are the cheap bit so go for the best you can find.

What you don't tell us is old is the car and how many miles it has done.

Ted
Ted Newman

Gian, how old is your car, and what model is it (1.8i or VVC?)

If a pre-1999 car, then by all means change the head gasket- although this is not absolutely necessary, UNLESS the engine had been over heating as a result of the leaks you found- in which case, it could be a sensible precaution.

If you decide to replace the head gasket, then either the Mike Satur gasket or the very latest spec MG item will do. You should also get the plastic head locator dowels replaced with the current specification steel items.

If you have an older 1.8i, then get the inlet manifold gasket replaced as well as a precautionary measure. As has been discussed recently on the BBS, the later 'Green' coloured gaskets are far more durable than the earlier 'black' items.

Hope you are back on the road soon and enjoying your MG Gian! :o)
Rob Bell

Thanks guys,
the car is 1997 Mpi and has done 60.000 Km (37.000 miles) so far.
As you have suggested the mechanic saw the manifolds and said I should change them also.
So, if I order the HG from Mike Satur do you think it comes with everything needed to install it (steel dowels?) or something should be ordered anyway from Rover?
Thanks again for your advice.
Gian Marco
Gian Marco Mazzocchi

I'm not sure whether Mike's gasket comes with the steel dowels, or has to be ordered separately. Best to check when ordering from him Gian.
Rob Bell

Gian, I would recommend the latest Rover gasket and the Rover steel dowels....
David

Gian,
Where exactly is the problem 'stopper' (core plug)
Located?.
It seems extreme to have to remove the engine to fix this...
Mark.
MARK PERKS

The K Series engine block doesn't have any core plugs.....
Dave

Dave,
any ideas about a coolant leak to the gearbox though ?
Dieter Koennecke

Thanks Dave - bit like a musical act that remark - we are all sitting waiting for the punch line....

Ted
Ted

The head gaskets we supply can be ordered with or without steel dowels, generally we send them out with the dowels, HTH.
Mike.
mike

This thread was discussed between 11/03/2002 and 12/03/2002

MG MGF Technical index

This thread is from the archives. Join the live MG MGF Technical BBS now