Welcome to our Site for MG, Triumph and Austin-Healey Car Information.
MG MGF Technical - got the wiper motor in.....finally
| Hi, got a bit desperate yesterday when the Fiesta 'spare car' got big problems with a drive shaft. Axle gaiter damaged and I think dust and mud got to the shaft. Steering nearly impossible. Me and no car for rainy conditions. And only cause my dealer was for thee month now unable to get a spare for me. They forgot to reinstall the black shredder Angry call to my workshop this morning. I wondered in any way, why they and just this dealer couldn't get one ;) BTW it is a sub location of Auto Becker Dusseldorf. Now obviously nearly in incomposition before bankruptcy. Dooh ! But that is another story. Anyway, long discussion and me shouting. Nothing but troubles and confusion there. I had already looked up Mike Saturs phone number +441709890555... :) Then a call from the poor friendly workshop head. 'I got one out from a MY2000 show car, but the connector will be different to your MK1', he said. Anyway I need a wiper. Picked it up and promised to giving back the old noisy in next week. Did some pictures. I dismantled the motor only, not the complete assy as done by Bruce recently. It is possible, but needs thin fingers and lots of patience. I cut off the connectors then and soldered the 5 wires together at each. Wire colours are the same at both. Used a lot of isolation tape to prevent the harness from bending and short cuts of the wires. Got it in as well without major problems and it is so silent :) Required tools: Philips driver to remove the black shredder. 10mm ring and fork spanner for the hiden three motor fixture bolts. Same in 13mm for the gearbox axle. I hope it will last for ever now. Added some pictures somewhere on this page. http://www.mgf-net.de/wiper/index.htm Nothing very important. The new is as bad sealed as the old. Cheers Dieter |
| Dieter Koennecke |
| Nice one Dieter! Hope it lasts as long as mine has. The pictures of a LHD under bonnet are interesting, so much more room. cheers Bruce |
| Bruce Caldwell |
| Well, I´ve been trying to get my wiper assy together again. 3 of the 4 ball joints failed (seems to be a common prob on the Rover 800 series)http://www.mgfcar.de/wiper/cp_4461.jpg. Drilled holes and put M4 through with counter bolt. Unfortunately center joint had 1 bolt to many, as the whole hinges, it obstructed movement of the assy and caused the motor to break down. Desperately looking for a second hand unit now. cheers, wiperless David. *LOL* |
| david |
| Don't worry, summer is near ;) BTW, no chance to find the OEM in the UK ? I'm afraid but getting second hand parts on the continent is nearly impossible. Netherlands is IMO an option, cause they keep everything. In D the guys sell total loss cars almost 'anywhere', but the parts never appear on the web. You currently can get a complete 'fresh rolled' MGF from a german guy. But he believes to get 3100 EUR for the heap of scrap. Though, Cor Veerhuis from the dutch MGA Owners club may have one for sale. Rgds Dieter |
| Dieter Koennecke |
| Remember not to swap the wipper arms over, especially if the windowscreen trim is not fitted. You can crack the windowscreen. "I was lucky it only took a piece out", which the plastic trim covered. Richard |
| Richard |
| Dieter: unfortunately in Belgium "summer" is no the equivanlent to "dry" ;-( Richard, what do you mean by "swap the wiper arms over"? Interchanging LH and RH arm? I got a price quote from Bromsgrove, second hand £45 +VAT + £24 transport. Surely cheaper than a new one on the continent. It is a MKY 2000 so I might be facing the same problems as Dieter had. Any other suggestions for cheap second hand parts for the *F* in the UK. Tried B&G, but didn´t get a reply. I´ll give them a ring, cheers, David. |
| David |
| David, if you order one, then just take two complete assies or more to share shipment costs. Will be no problem to getting rid of. I currently know another german who is after one. If you like than I'll take contact to him. |
| Dieter Koennecke |
| Dieter. The wipper arms L/H & R/H and can not be changed over, especially if the windowscreen bottom trim is not fitted. The wrong wipper arm will rub/crack the windowscreen bottom edge. Richard. |
| Richard |
| Dieter, The above needs VAT to be added. I´m willing to place a double order, if we/he can find a way for delivery to Germany. Time for another meeting I guess. David. It seems there is a difference between a LHD and a RHD wiper assy, true? |
| David |
This thread was discussed between 09/03/2002 and 12/03/2002
MG MGF Technical index
This thread is from the archives. Join the live MG MGF Technical BBS now