MG-Cars.info

Welcome to our Site for MG, Triumph and Austin-Healey Car Information.

Recommendations

Parts

MG parts spares and accessories are available for MG T Series (TA, MG TB, MG TC, MG TD, MG TF), Magnette, MGA, Twin cam, MGB, MGBGT, MGC, MGC GT, MG Midget, Sprite and other MG models from British car spares company LBCarCo.

MG MGF Technical - Kangaroo-ing on down, sport

Hi Guys,

Wonder if you all may be able to help. My '96 1.8i has developed an intermittent fault- it kangaroos down the road on part throttle in 2nd/3rd gear with part throttle. Release the throttle temporarily and the engine picks up again, and performs normally!

I haven't noticed any performance deficit what so ever.

I thought it may have been some 'dirty' petrol, but I've filled up again since this started, and 'Skippy the kangaroo- god' of K-series faults has struck back!

What on earth is going on?

Thoughts have centred on fueling or an ignition problem (but I replaced the spark plugs and leads just 6 months ago). What should I be looking at?

Help! I want to exocise the spirit of Skippy from my F!
Jon

<FX 'CLICK' lights go off, draws knife>
It could be that the fuel filter needs replacing.
It could be that MEMS has some faulty information about fueling at this point in the rev range.
MEMS learns how to fuel your engine most effectivly, however if this info gets mashed at a particular locaton (say 3k rpm) then when it hits this speed it will incorrectly fuel the engine causing a loss in power, after the revs fall to another watermark it will correctly fuel the engine, resulting in a better takeup and the car will "hop".... try removing the battery overnight - failing that a visit to the dealer for a testbook reset?

<FX 'CLICK'>
<FX looks at knife>
Did I hit anything?

Will
Will Munns

Could a faulty distributer cap or rotor arm cause this? Not sure, but electrical faults are notorious for triggering intermittent faults such as this...
Rob Bell

You don't need to disconnect the battery to reset the MEMS. I forget the procedure - Dieter knows (have a look in the archives in the meantime).

How about a sticking throttle as another possibility?
Dot

The "push the accelerator to the floor five times with the engine on but not running" method only resets the throttle position sensor, not the fueling map- but it could be this which is wrong?
Other thought, could the throttle position sensor be faulty at this position (thinks carbonized pot), unlightly because it must (for some value of must!) be potected from the outside world (so no beer ingress like lighting desks eh paul!) and the current must be farly low (negligable I would hope), and the wiper should be run up and down fully regularly (or you shouldn't be driving a sports car!)

Will
Will Munns

I don't think its a sticking throttle Dot- there doesn't seen to be any differences in pedal resistance.

Will, thanks for your stab in the dark... I hope you got Skippy! The fuel filter sounds like a simple thing to check.

Rob, will check the dizzy and rotor arm.

A MEMS fault? Oo-er! I don't like the sound of that. :-( I sincerely hope not; sounds expensive!
Jon

Thanks Will for the throttle position sensor suggestion. How best to check on this?
Jon

Sorry Jon, meant the throttle body...
Dot

Jon,
the fuel filter is in a pressureized part of the fuel system- so leave the car to sit first, be careful and ready with a rag to catch the petrol(there wont be much of it to releive the pressure), and do wear latex gloves, they don't cost much, but will stop petrol penetrating your skin!
The throttle position sensor can be reset as stated (and it don't cost anything to try), but if it is gunked up then doing this may clean it up. To test if it has deteriated you will need a multimeter, go to the throttle body and you should find some wires attached(sorry I only know exactly where it is on the 214- DIETER? ), if you take these off (they should be secured with a spring clip) and slap the meter across the terminals on the throttle body, then moving the throttle with your hand you should see a smooth movement across the meter, jerks (espacially to zero) indicate a damaged sensor. This is highly unlightly, I have not heard on one failing before - but if it has then I see an ideal opertunity to _have_ to replace the entire unit with a trophy body!

Will
Will Munns

This thread was discussed on 14/03/2002

MG MGF Technical index

This thread is from the archives. Join the live MG MGF Technical BBS now