MG-Cars.info

Welcome to our Site for MG, Triumph and Austin-Healey Car Information.

Recommendations

Parts

MG parts spares and accessories are available for MG T Series (TA, MG TB, MG TC, MG TD, MG TF), Magnette, MGA, Twin cam, MGB, MGBGT, MGC, MGC GT, MG Midget, Sprite and other MG models from British car spares company LBCarCo.

MG MGF Technical - Water in sills?

My 96 vvc seems to have been picking up water during the recent wet weather and I can now hear it sloshing around somewhere in the area of the passenger side sill. The floor & carpet is bone dry.

Does anyone have any ideas as to how it might have got in there, and better still how best to get it out!?
Your expert suggestions would be much appreciated please.

Thanks

Nick
Nick Pinches

Check the water drain in the underside of the door.

Ted
Ted Newman

Ted

Sorry, I should have mentioned that I have checked that the drain holes in the doors are clear.

Nick
Nick Pinches

Ok:-)

I must confess that I am not sure about the *F* but most cars that I have owned have also had drainage holes in the cills as well which can become easily blocked with mud and other debris.


The only other thing I can think of is the body stiffener panel bolted onto the underside of the car immediatley under the seat area, this looks as though it could be capable of holding water (if it gets in) and sloshing around.

Ted
Ted Newman

Ted

Thanks. I'll have a closer look where you suggest.

Nick
Nick Pinches

Sounds bad!
Have you had any bodywork repairs done - or a previous owner? Years ago I had a Merc which had a frontal shunt. When I got it back, I had that problem. The repairers had fixed new wings on etc, and had left a hole in the wheelarch which allowed water into the cills. When braking/accelerating, you could hear it sloshing around. Its very bad news for the logevity of the car!
T Green

T Green

Yes, the car had a frontal shunt about 4 years ago but the problem has only just come to light (or sound!).
If no-one else has experienced this problem it sounds as if it might be linked to this.

I know I need to get the water out, but also to stop it coming back in!

Nick
Nick Pinches

I had some work done to a mini ie new sills and when it rained somehow the water got into the new sills and from there through a tiny hole into the drivers footwell

if I jacked the car up water would come out of the end of the sill.
so i recommend getting your car on some serious slopes to see if water is coming out of anything.
it doesnt bode well mate!
the mini was fixed with clear bath sealant
invisible and effective.

N
Neil

Drill a small hole (1mm) into the sills where you think the water is trapped. If it drains out then make the hole slightly bigger, say 6mm and put some underseal on the bare metal exposed. Leave the hole as a permanent drain hole. Better to have the water out than in.
If water doesn't drain out of the small hole that you made then plug it with sealant and a self tapping screw. Try again somewhere else.

Bruce
Bruce Caldwell

Agree with Bruce

In addition get the inside of the sill treated with waxoyl to prevent "rusting out"

Do this both sides - just in case - most garages do this for little money
tony

Hi,

not sure whether I'm on the right subject, though.
May be total wrong. Im sorry in advance :)

I believe the drain holes are at the jack up locations, two of at each side. If they got bended, then may be they get blocked.
Water could get in from the front and rear wheel house.
There are weld lines which should be sealed, and rubber plugs to close the holes to the sill.

Regards
Dieter

Dieter Koennecke

Bruce, Tony & Dieter

Many thanks for your suggestions and ideas as to where to look and what to do.

Dieter; are the rubber plugs fitted in the drain holes by the jacking points (would not seem logical) or are they near the weld lines in the front and rear wheel arches?

Nick
Nick Pinches

For the record, thought you might like to know that I managed to drain about 3 pints of water out yesterday. I found a drain hole where Deiter had suggested, at the jacking point. It had got blocked. A quick wiggle and poke with a fine screwdriver cleared it ok.
Water was getting in at a poorly welded joint at the front of the sills just under the lower door hinge.

Thanks to everyone who helped me track this down.

Nick
Nick Pinches

well done :)

The grommets I talked of are at the lower ends of the wheel arch.

Regards
Dieter
Dieter Koennecke

This thread was discussed between 12/03/2002 and 18/03/2002

MG MGF Technical index

This thread is from the archives. Join the live MG MGF Technical BBS now